PDM CAN CONFIGURATION NEW CHANNEL VALUES AND RESOLUTION

Discussion and support for MoTeC Power Distribution Modules

PDM CAN CONFIGURATION NEW CHANNEL VALUES AND RESOLUTION

Postby jrvcompeticion on Tue Nov 09, 2021 3:35 pm

Hi
I want to add some new can bus channels in my PDM, so I can see: engine oil pressure and intake air temperature.
To set the intercooler water pump output and set the engine start conditioned to a minimum oil pressure, but I can't find the channel setting. This information if I can see it on my C125 diplay

Image
jrvcompeticion
 
Posts: 5
Joined: Tue Nov 09, 2021 3:10 am

Re: PDM CAN CONFIGURATION NEW CHANNEL VALUES AND RESOLUTION

Postby SDean on Tue Nov 09, 2021 3:56 pm

Hi,

I have attached a C125 configuration and a PDM configuration with some basic channels configured.
Attachments
PDM Transmit.pdm
(17.77 KiB) Downloaded 54 times
PDM Transmit.c125v64
(1.34 MiB) Downloaded 54 times
Stephen Dean
MoTeC Research Centre Melbourne, Australia
User avatar
SDean
Site Admin
 
Posts: 1003
Joined: Tue Dec 02, 2014 9:29 am
Location: Melbourne

Re: PDM CAN CONFIGURATION NEW CHANNEL VALUES AND RESOLUTION

Postby jrvcompeticion on Tue Nov 09, 2021 5:57 pm

Thank you very much for your answer
The problem is that I think that I have already used those channels,
I attach the files so you can check them

Thank you very much
Attachments
PDM30_jrv_test.pdm
(72.37 KiB) Downloaded 47 times
C125_MoTeC_2021_JRV_ test.c125v61
(873.64 KiB) Downloaded 49 times
jrvcompeticion
 
Posts: 5
Joined: Tue Nov 09, 2021 3:10 am

Re: PDM CAN CONFIGURATION NEW CHANNEL VALUES AND RESOLUTION

Postby jrvcompeticion on Wed Nov 10, 2021 7:23 am

I finally managed to visualize the channels,
But there is something that is still not right.
The channel of: Engine oil pressure, shows a value of approximately 200 kpa, when the real value is 100 kpa and the inlet air temperature channel, shows a value of 175ºC when the real value is 17.5º C
I have added a channel, in CAN1 of Diplay C125, with the name CAN.C125.108.JRV

What's wrong with the settings?

Sorry for the way I speak, I don't speak English

Thank you very much, your help is very important.
Attachments
PDM30_Ford_3_9.5.0_JRV.pdm
(77.14 KiB) Downloaded 46 times
C125_MoTeC_2021_JRV.c125v64
(1.36 MiB) Downloaded 45 times
jrvcompeticion
 
Posts: 5
Joined: Tue Nov 09, 2021 3:10 am

Re: PDM CAN CONFIGURATION NEW CHANNEL VALUES AND RESOLUTION

Postby SDean on Wed Nov 10, 2021 2:04 pm

Hi,

Try this Dash calibration.
Attachments
C125_MoTeC_2021_JRV.c125v64
(1.36 MiB) Downloaded 54 times
Stephen Dean
MoTeC Research Centre Melbourne, Australia
User avatar
SDean
Site Admin
 
Posts: 1003
Joined: Tue Dec 02, 2014 9:29 am
Location: Melbourne

Re: PDM CAN CONFIGURATION NEW CHANNEL VALUES AND RESOLUTION

Postby jrvcompeticion on Fri Nov 12, 2021 8:15 pm

SDean wrote:Hi,

Try this Dash calibration.


OK thank you very much. I already get all the correct data. You are the best
;)
jrvcompeticion
 
Posts: 5
Joined: Tue Nov 09, 2021 3:10 am


Return to PDM15 PDM16 PDM30 and PDM32

Who is online

Users browsing this forum: No registered users and 2 guests

cron