OBD-II to Display Loom

Part No: #61197

The OBD-II loom is a plug-in adaptor that connects the C1212 terminated loom (supplied in C1212 Race Kits) to the standard, on-board diagnostics port of many modern vehicles.

This enables the C1212 to display and log a selection of channels, which differs from car to car.

Vehicle compatibility will vary from region to region, but as a guide most cars built after 2007 have an OBD-II connector.

Download datasheet

CAN ECU to Display Loom

Part No: #61198

This plug-in adaptor joins the C1212 terminated loom (supplied in C1212 Race Kits) to the standard MoTeC CAN communications connector used by MoTeC M84, M400, M600 or M800 ECUs. It makes 70+ ECU channels available to the C1212.

This loom will also work with other manufacturers' CAN-based ECUs, with the exception that the round AMP connector must be removed and replaced with a suitable connection for the relevant ECU.

Download datasheet

RS232 ECU to Display Loom

Part No: #61199

The RS232 ECU loom joins the C1212 terminated loom (supplied in the C1212 Race Kits) to the D9 RS232 communications connector used by MoTeC M4, M48 or M8 ECUs.

This loom will also allow connection to many other RS232-based aftermarket ECUs; custom communication templates may be required.

The RS232 ECU loom can provide 40+ ECU channels to the C1212.

Download datasheet

C1212 I/O Loom

Part No: #61259

This is a high quality, ready made loom that adds 6 analogue voltage inputs and 2 analogue temperature inputs to your C1212 terminated loom, quickly and easily. The loom has been made so that it is simple to install, with minimal wiring required. Each of the eight 2 metre leads is individually twisted and heat shrunk for a professional finish.
 
To use this loom the optional C1212 I/O Upgrade must be enabled.

Curly Cord

Part No: #61222

Our plug-in curly cord allows the C1212 Race Kit buttons to be moved onto the steering wheel with ease. The loom is pre-terminated with a 6 pin DTM, and has 6 straight through wires, allowing for additional buttons if required.

Download datasheet

Ethernet Cable

Part No: #61225

To configure the C1212, a communication cable is required to connect to a PC. An Ethernet cable should be used to connect to the Ethernet port on the PC.

Note: An Ethernet Communications Cable is included with the C1212 Race Kits.

Two Button Loom

Part No: #61221

• Pre-wired with a terminated, plug-in loom
• Can be mounted in the steering wheel using the optional Curly Cord
• Curly Cord also provides the flexibility to add extra buttons

Race Terminated Loom

Part No: #62204

The Race Loom provides convenient and easy connection of the C125 Race kit to your vehicle. It allows connection of the C125 to power, ethernet, ECU, GPS and buttons. Also, the loom has an Accessory lead that can be used to connect a MoTeC CAN based product, such as an LTC, Expander, V2, etc.

Mating Connector

Part No: #65044

34 pin waterproof connector including sockets.

SLM-C

Part No: #18122

The Club Shift Light Module (SLM-C) provides eight fixed colour LED indicator lights in a compact array. The lights are arranged in a pre-defined shift light pattern. The colour intensity of the LEDs can be set to your preference.

SLM

Part No: #18120

The Shift Light Module (SLM) may be used for shift lights, warning lights or other indicators as programmed by the user.
It provides eight multicolour LED indicator lights in a compact array. The colour, intensity and purpose of each LED can be controlled independently, providing enormous flexibility and scope for customisation.

PAL Bullet Camera (12v)

Part No: #61285

This 12v Colour Bullet CCD Camera with PAL output signal allows for a signal input into a colour display for viewing live on screen imagery. Can be used as a reverse camera, and displayed under user derived conditions or via a driver operated switch. The C12x screens can display 1 camera signal, with the C18x displays capable of displaying up to 3 camera inputs.

SMS Module

Part No: #61286

The SMS module, once fitted with a SIM card, allows mobile phone SMS text messages to be displayed on the screen.

Download datasheet

Custom USB Logging Cable A Panel/ Mini B

Part No: #61279

Required cable to allow a USB drive to be connected to the Display Logger.

Note: Requires the USB Logging enable (C1212 #29813)

MoTeC 32Gb Data Plug

Part No: #61280

High temp and vibration USB drive with a capacity of 32Gb, with locking ring for use in motorsport applications.

Note: Requires the USB Logging enable (C1212 #29813)

32Gb USB3 Flash Drive

Part No: #61292

High temp and vibration USB drive with a capacity of 32Gb allowing for days of continuous logging.

Note: Requires the USB Logging enable (C1212 #29813)

GPS

GPS-L10 Part No: #41304,  GPS-L5 Part No: #41305

GPS units can be used with the C1212 for speed, position, track mapping and lap timing, plus date, time and GPS statistics.

Note: A 10 Hz GPS is included with the C1212 Race Kits.

Lap Timing

Part No: #15512

GPS units are often utilised as a cost effective method of lap timing (see above). The MoTeC BR2 Beacon Receiver is an alternative.

Sensors

A vast range available.

Lambda  Temperature   Pressure   Pitot   Crank, Cam and Speed   Position   Force and Motion  Switches

Expanders

E888 Part No: #14007,  E816 Part No: #14008

MoTeC's E888 or E816 Expanders can be connected to the C1212 with full functionality.