The MoTeC Logo
Welcome
Products
Downloads
Training
Forum
FAQ
Careers
Dealers
Products
The MoTeC Logo
Welcome Products Downloads Training Forum FAQ Careers Dealers
The MoTeC Logo
DMC D - Dual Magnetic Convertor
DMC D - Dual Magnetic Convertor
DMC D - Dual Magnetic Convertor
Part No: #53118

OVERVIEW

Three versions of Dual Magnetic Converters (DMCs) are available (A, C and D). DMCs convert magnetic style signals to an open collector output signal (square wave). This makes a typical magnetic sensor behave as a switched or hall effect sensor, thus making the signals suitable for use with ECUs and loggers. A single DMC can convert two independent magnetic sensor signals.

INTENDED USE

This DMCD, is intended for use with magnetic wheel speed sensors.
All DMC versions contain trim pots. At manufacture, these are pre-set to specification for the relevant DMC version, they should not be adjusted after purchase.

OPERATION

The signal should be symmetrical about zero volts.The polarity of the sensor connection is generally not important. For sensors that have a distinct positive or negative going waveform, then negative going is preferred for more accurate dectection. The measuring equipment should be configured to use the negative going edge if possible; however, positive going edge will also generally work satisfactorily. To minimise the possibility of interference at the low trigger levels, this model includes heavy filtering that results in significant variation of the trigger level with frequency. The variation is tailored to match a typical sensor where the output signal increases as the frequency increases.

AVAILABLE DMC VERSIONS

Two other versions are available to cater for different purposes and different trigger levels:

DMCA — used for fuel flow sensors that have a very low trigger level.

  • 53111 – DMCA - DUAL MAGNETIC CONVERTOR FOR FUEL FLOW SENSORS

DMCC — used as a conditioner for ignition system inputs.

  • 53117 – DMCC - DUAL MAGNETIC CONVERTER - GENERAL PURPOSE

SPECIFICATIONS

Physical

  • Built into Deutsch DTM04-12P connector housing
  • Deutsch DTM06-12S (MoTeC #68058) connector

Ambient Operating Temperature

  • -10 °C to 85 °C

Input resistance

  • 43 kΩ

Maximum input voltage

  • 120 Vpp

Minimum input signal level required for triggering

Frequency (Hz) Peak to Peak level (Vpp)
<=10 0.4
100 0.5
200 0.7
500 1.6
1000 3.0
2000 5.8
5000 14.0

INPUT CHARACTERISTICS

The signal is not inverted.

OUTPUT CHARACTERISTICS

Characteristic Description
Type Open collector MOSFET
On resistance Approximately 0.2 Ω
Maximum continuous current 0.5 A
Protection Shut down at approximately 5 A (reactivates on each cycle of the input signal)

PINOUT

Mating connector: Deutsch DTM06-12S (MoTeC #68058)

Pin Function
1 Power positive (6 V to 16 V — normally 6 V from ADL
2 Not connected
3 Not connected
4 Not connected
5 Input 1
6 Input 2
7 Output 2 (open collector type, no pull-up — normally connected to ADL Digital In)
8 Output 1 (open collector type, no pull-up — normally connected to ADL Digital In)
9 Not connected
10 Not connected
11 0 V to both sensors
12 Power negative (normally 0 V at ADL)

PURCHASING

If you are interested in purchasing this product contact an Authorised MoTeC Dealer.

DOWNLOADS

Useful Links

This page shows the relevant downloads for this product. For a full selection of MoTeCs downloads visit the Downloads page.

 

To keep up-to-date with the latest webinars or software you can subscribe to our mailing lists and we will send you a message when new items are released.

To sign-up for a mailing list click the "SIGN-UP: WEBINAR NEWS" or "SIGN-UP: SOFTWARE RELEASE" button below.

OVERVIEW

INTENDED USE

OPERATION

AVAILABLE DMC VERSIONS

SPECIFICATIONS

INPUT CHARACTERISTICS

OUTPUT CHARACTERISTICS

PINOUT

PURCHASING

DOWNLOADS