The MoTeC Logo
Welcome
Products
Downloads
Training
Forum
FAQ
Careers
Dealers
Welcome
The MoTeC Logo
Welcome Products Downloads Training Forum FAQ Careers Dealers
The MoTeC Logo

PDM40

A NEW BENCHMARK IN INTELLIGENT POWER MANAGEMENT

FIRST LOOK - NEW FOR 2027

As PMW Expo opens its doors for 2026 in Cologne, Germany, the professional motorsport industry will witness the global debut of the new MoTeC PDM40. Next generation hardware, familiar but evolved software, and an impressive package of features. Let's get to know the new MoTeC PDM40!

The MoTeC PDM40 redefines what a Power Distribution Module can deliver, combining high-current power distribution, advanced vehicle control, data acquisition and powerful communications within one rugged platform. It combines 40 main outputs, 8 low side outputs and a comprehensive range of analogue and digital inputs in one fully sealed, IP67 rated enclosure. It has a 200 A nominal current rating and is capable of higher transient peak currents.

High-side and half-bridge outputs of varying classes provide current measurement, programmable fusing and soft start and stop. Most outputs also have open-circuit, short-circuit and over-current diagnostic management. Half-bridge outputs support pulse width modulation and engine synchronous control, allowing the PDM40 to drive devices such as DC servo motors, current controlled solenoids and two-speed wiper motors.

A dedicated standby output provides power isolator relay management, enabling the PDM40 to control devices such as a battery isolator directly.

4 CAN buses, 10/100 Ethernet, 2 Automotive Ethernet interfaces and 2 RS232/TTL/LIN serial ports give the PDM40 the flexibility to communicate with a wide range of devices in the vehicle. Two integrated Wideband Lambda inputs and multiple analogue and digital inputs with switchable pull allow it to acquire data directly, with built-in data logging.

The PDM40 is configured within Tune 1.6, the same software used across MoTeC’s M1 ECU platform. A visual, block-based programming workspace makes complex logic quick to build, while the virtual scope lets you take live measurements while configurations are still being developed and assists with diagnosis and fault finding once the vehicle is running. Build it, see it, test it.

HARDWARE

FEATURES

  • 200 A nominal current rating - capable of higher transient peak current
  • 40 x Main Outputs: high-side and half/full bridge of varying classes - with current measurement
  • 8 x Low Side Outputs
  • 4 x Sensor Supply Outputs (5V), with over current protection and current monitoring
  • Most outputs have open circuit, short-circuit and over-current diagnostic management
  • Surlok Plus® positive and negative quick release power connectors
  • Reverse power and transient protection
  • Operation of all features down to 6V
  • Power isolator relay management with dedicated standby output (e.g. battery isolator)
  • Separate standby power input for a range of low-power installations (< 1mA standby current)
  • Flexible wake from low-power standby - wake from CAN, Ethernet, standby inputs, time and IMU
  • Analogue and digital inputs with switchable pull of various classes
  • 2 x integrated Wideband Lambda Inputs
  • 4 x CAN buses with switchable termination - 2 CAN FD compatible
  • 10/100 Base-Tx Ethernet interface
  • 2 100/1000Base-T1 Automotive Ethernet interfaces
  • 2 serial ports (RS232 / TTL / LIN capable)
  • Real-time clock
  • 6 axis inertial measurement unit (16 G)
  • 4 x Status LEDs - 1 x user configurable
  • Fully sealed, IP67 rated enclosure.
  • Device management with M1 Tune 1.6
  • Flexible block-based logic for device configuration
  • Dynamic CAN bus configuration for transmit and receive
  • Live data viewing
  • Data Logging

Specifications are subject to change.

INPUTS AND OUTPUTS

The PDM40 features multifunctional input and output pins designed for flexibility, with each pin class offering a different combination of capabilities.
Refer to the pin descriptions below for details and typical applications.

SOFTWARE

The new PDM40 is configured within MoTeC’s Tune 1.6 software, an update on the familiar M1 ECU tuning tool. Its NEW visual block-based programming environment provides the flexibility to develop complex control strategies quickly, while the virtual scope brings live measurement and diagnostics directly into the configuration workflow.

Tune 1.6 Features include:

  • COMPUTE: a new dedicated Visual Programming subsystem for PDM40 configuration
  • COMMS: a dynamic CAN import and export subsystem for flexible comms configuration
  • COMPUTE Wizard for lightning fast setup of commonly used functions, e.g. wipers and indicators
  • SCOPE for visualising live COMPUTE measurements while building and testing configurations
  • Visual CAN network representation and configuration
  • Visual representation of keypad buttons and functions
  • M1-class data logging and analysis capability
  • Extensive help including dynamic pinout visualisation
Virtual Scope
Adding Keypad Buttons

SPECIFICATIONS

  • Size 174 x 171.5 x 47.3 mm
  • Weight 1030 g
  • 1 x 60 pin connector (waterproof when fully populated)
  • 1 x 94 pin connector (waterproof when fully populated)
  • 2 x 8mm Surlok Plus® 35/50mm2 user configurable power connectors
  • REACH and RoHS compliant/IMDS available.

Specifications are subject to change.

AVAILABILITY

The PDM40 will be available Q2 2027 through our global Dealer network.